agilent 2 mm x 5 mm rectangular led lamps data sheet hlmp-s100, hlmp-s201, hlmp-s301, hlmp-s400, hlmp-s401, hlmp-s501, hlmp-s600 package dimensions features ? rectangular light emitting surface ? excellent for flush mounting on panels ? choice of five bright colors ? long life: solid state reliability ? excellent uniformity of light output description the hlmp-s100, -s201, -5301, -s400, -s401, -s501, -s600 are epoxy encapsulated lamps in rectangular packages which are easily stacked in arrays or used for discrete front panel indicators. contrast and light uniformity are enhanced by a special epoxy diffusion and tinting process. the hlmp-s100 uses double heterojunction (dh) absorbing substrate (as) aluminum gallium arsenide (algaas) leds to produce outstanding light output over a wide range of drive currents. 2.41 (0.100) 2.03 (0.085) 2.23 (0.088) 1.98 (0.078) 8.00 (0.315) 7.37 (0.290) 25.40 (1.00) min. cathode lead bottom view side view 1.27 (0.50) nominal notes: 1. all dimensions are in millimeters (inches). 2. an epoxy meniscus may extend about 1 mm (0.040") down the leads. 3. there is a mximum 1 taper from base to the top of lamp. 2.54 (0.100) nominal 0.46 (0.018) sq. nominal 5.46 (0.215) 4.95 (0.195) 5.18 (0.204) 4.93 (0.194)
2 selection guide luminous intensity iv (mcd) at 20 ma color part number min. typ. max. algaas red hlmp-s100 3.4 7.5 C her hlmp-s201 hlmp-s201-d00xx 2.1 3.5 C hlmp-s201-e00xx 3.4 7.5 C hlmp-s201-ef0xx 3.4 7.5 10.8 orange hlmp-s400 2.1 3.5 C hlmp-s401 3.4 7.5 C yellow hlmp-s301 hlmp-s301-b00xx 1.4 2.1 C hlmp-s301-c00xx 2.2 4.0 C hlmp-s301-cdbxx 2.2 4.0 7.2 green hlmp-s501 hlmp-s501-c00xx 2.6 4.0 C hlmp-s501-d00xx 4.2 8.0 C hlmp-s501-de0xx 4.2 8.0 13.4 emerald green [1] hlmp-s600-a00xx 1.0 3.0 C note: 1. please refer to application note 1061 for information comparing standard green and emerald green light output degradation. part numbering system hlmp - s x xx - x x x xx mechanical option 00: bulk 02: tape & reel, straight leads dg: ammo pack color bin options 0: full color bin distribution b: color bins 2 & 3 only maximum iv bin options 0: open (no max. limit) others: please refer to the iv bin table minimum iv bin options please refer to the iv bin table brightness level 00: less brightness 01: higher brightness color options 1: algaas red 2: gap her 3: gap yellow 4: gap orange 5: gap green 6: gap emerald green
3 electrical/optical characteristics at t a = 25 c sym. description device hlmp- min. typ. max. units test conditions 2 q 1/2 included angle between half all 110 deg. i f = 20 ma luminous intensity points see note 1 l peak peak wavelength algaas red 645 nm measurement at high efficiency red 635 peak orange 600 yellow 583 green 565 emerald green 558 l d dominant wavelength algaas red 637 nm see note 2 high efficiency red 626 time const, e -t/ t s orange 602 yellow 585 green 569 emerald green 560 t s speed of response algaas red 30 ns high efficiency red 90 orange 280 yellow 90 green 500 emerald green 3100 c capacitance algaas red 30 pf v f = 0; f = 1 mhz high efficiency red 11 orange 4 yellow 15 green 18 emerald green 35 r q j-pin thermal resistance all 260 c/w junction to cathode lead at seating plane v f forward voltage algaas red 1.6 1.8 2.2 v i f = 20 ma her/orange 1.5 1.9 2.6 yellow 1.5 2.1 2.6 green/emerald 1.5 2.2 3.0 green v r reverse breakdown voltage all 5.0 v i r = 100 ma h v luminous efficacy algaas red 80 high efficiency red 145 orange 380 lumens/ see note 3 yellow 500 watt green 595 emerald green 656 notes: 1. q 1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 2. the dominant wavelength, l d , is derived from the cie chromaticity diagram and represents the single wavelength which defines the color of the device. 3. radiant intensity, i e , in watts/steradian, may be found from the equation i e = i v / h v , where i v is the luminous intensity in candelas and h v is the luminous efficacy in lumens/watt. 4. please refer to application note 1061 for information comparing standard green and emerald green light output degradation.
4 figure 1. relative intensity vs. wavelength. absolute maximum ratings at t a = 25 c high efficiency red/ green/ parameter algaas red orange yellow emerald green units peak forward current 300 90 60 90 ma average forward current [1] 20 25 20 25 ma dc current [2] 30 30 20 30 ma transient forward current [3] 500 ma (10 sec pulse) led junction temperature 110 110 110 110 c operating temperature range -20 to +100 -55 to +100 -55 to +100 -20 to +100 c storage temperature range -55 to +100 -55 to +100 wave soldering temperature [1.59 mm (0.063 in.) from body] 250 c for 3 seconds solder dipping temperature [1.59 mm (0.063 in.) from body] 260 c for 5 seconds notes: 1. see figure 5 to establish pulsed operating conditions. 2. for algaas red, red, orange, and green series derate linearly from 50 c at 0.5 ma/ c. for yellow series derate linearly from 50 c at 0.34 ma/ c. 3. the transient peak current is the maximum non-recurring peak current that can be applied to the device without damaging the l ed die and wire bond. it is not recommended that the device be operated at peak currents beyond the peak forward current listed in the absolute maximum ratings. orange high efficiency red wavelength C nm relative intensity 1.0 0.5 0 500 550 600 650 700 750 yellow emerald green high performance green t a = 25 c algaas red
5 figure 4. relative efficiency (luminous intensity per unit current) vs. led peak current. h v (300 ma) for algaas red = 0.7. figure 2. forward current vs. forward voltage characteristics. v f (300 ma) for algaas red = 2.6 volts typical. figure 3. relative luminous intensity vs. dc forward current. figure 5. maximum tolerable peak current vs. peak duration. (i peak max determined from temperature derated i dc max). figure 6. relative luminous intensity vs. angular displacement. i f C forward current C ma 1.0 v f C forward voltage C v 0 20 40 60 2.0 3.0 90 70 green/emerald green yellow red algaas red 10 30 50 80 4.0 5.0 t p C pulse duration C s algaas red 3 1 10 10 10000 1000 100 1 3 khz 10 khz 1 khz 300 hz f C refresh rate C 100 hz 2 9 8 7 6 5 4 ratio of maximum peak current to temperature derated maximum dc current i peak max. i dc max. ratio of maximum tolerable peak current to maximum tolerable dc current 1 t p C pulse duration C s her, orange, yellow, and green 1.0 2.0 3.0 10,000 1000 4.0 1.5 100 10 i peak max. i dc max. 100 khz 30 khz 10 khz 3 khz 1 khz 300 hz 100 hz 10 100 40 70 20 60 80 30 50 90 0 10 20 30 40 50 60 70 80 90 1.0 0.6 0.8 0.2 0.4 relative luminous intensity (normalized at 20 ma) 0 i dc C dc current per led C ma 0 30 515 2.5 2.0 algaas red 0.5 1.0 1.5 10 20 25 her, yellow, emerald green peak C relative efficiency (normalized at 20 ma) 0 i peak C peak segment current C ma 0.4 0.6 0.8 1.0 90 20 70 50 40 1.3 1.1 green yellow red/orange algaas red 0.5 0.7 0.9 1.2 30 60 80 10 emerald green
6 intensity bin limits intensity range (mcd) color bin min. max. d2.43.8 e3.86.1 f6.19.7 g 9.7 15.5 h 15.5 24.8 i 24.8 39.6 j 39.6 63.4 k 63.4 101.5 l 101.5 162.4 m 162.4 234.6 n 234.6 340.0 red/orange o 340.0 540.0 p 540.0 850.0 q 850.0 1200.0 r 1200.0 1700.0 s 1700.0 2400.0 t 2400.0 3400.0 u 3400.0 4900.0 v 4900.0 7100.0 w 7100.0 10200.0 x 10200.0 14800.0 y 14800.0 21400.0 z 21400.0 30900.0 b1.62.5 c2.54.0 d4.06.5 e 6.5 10.3 f 10.3 16.6 g 16.6 26.5 h 26.5 42.3 i 42.3 67.7 j 67.7 108.2 k 108.2 173.2 yellow l 173.2 250.0 m 250.0 360.0 n 360.0 510.0 o 510.0 800.0 p 800.0 1250.0 q 1250.0 1800.0 r 1800.0 2900.0 s 2900.0 4700.0 t 4700.0 7200.0 u 7200.0 11700.0 v 11700.0 18000.0 w 18000.0 27000.0 intensity bin limits, continued intensity range (mcd) color bin min. max. a1.11.8 b1.82.9 c2.94.7 d4.77.6 e 7.6 12.0 f 12.0 19.1 g 19.1 30.7 h 30.7 49.1 i 49.1 78.5 j 78.5 125.7 green/ k 125.7 201.1 emerald green l 201.1 289.0 m 289.0 417.0 n 417.0 680.0 o 680.0 1100.0 p 1100.0 1800.0 q 1800.0 2700.0 r 2700.0 4300.0 s 4300.0 6800.0 t 6800.0 10800.0 u 10800.0 16000.0 v 16000.0 25000.0 w 25000.0 40000.0 maximum tolerance for each bin limit is 18%.
7 color categories lambda (nm) color category # min. max. 9 552.5 555.5 emerald green 8 555.5 558.5 7 558.5 561.5 6 561.5 564.5 6 561.5 564.5 5 564.5 567.5 green 4 567.5 570.5 3 570.5 573.5 2 573.5 576.5 1 582.0 584.5 3 584.5 587.0 yellow 2 587.0 589.5 4 589.5 592.0 5 592.0 593.0 1 597.0 599.5 2 599.5 602.0 3 602.0 604.5 orange 4 604.5 607.5 5 607.5 610.5 6 610.5 613.5 7 613.5 616.5 8 616.5 619.5 tolerance for each bin limit is 0.5 nm. mechanical option matrix mechanical option code definition 00 bulk packaging, minimum increment 500 pcs/bag 02 tape & reel, straight leads, minimum increment 1300 pcs/bag dg ammo pack, straight leads with minimum increment 2k/pack note: all categories are established for classification of products. products may not be available in all categories. please contact your local agilent representative for further clarification/information.
www.agilent.com/semiconductors for product information and a complete list of distributors, please go to our web site. for technical assistance call: americas/canada: +1 (800) 235-0312 or (916) 788-6763 europe: +49 (0) 6441 92460 china: 10800 650 0017 hong kong: (+65) 6756 2394 india, australia, new zealand: (+65) 6755 1939 japan: (+81 3) 3335-8152(domestic/interna- tional), or 0120-61-1280(domestic only) korea: (+65) 6755 1989 singapore, malaysia, vietnam, thailand, philippines, indonesia: (+65) 6755 2044 taiwan: (+65) 6755 1843 data subject to change. copyright ? 2001-2005 agilent technologies, inc. obsoletes 5988-4202en june 8, 2005 5989-3268en
|
